usg shaft wall details

United States Gypsum Company USG, Gypsum Board Shaft Wall Systems. Wall stud cavity are usually included as part of this section.

3 USG Shaft Wall Systems User’s Guide This brochure explains: – What a shaft wall system comprises Design Your System 21 Design Details Good Design Practices Specify Your

USG Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in 

Find commercial construction details including wall assemblies. The PURPLE Book II PDF General Information PDF Steel Stud Partitions PDF Shaftwall Assemblies PDF Stair Shaftwall Details PDF Elevator Shaftwall Details PDF Shaftwall Repair Details PDF

5()(5(1&( &855(17 8/ 6<67(06 ',5(&725< )25 $// *(1(5$/ - 5 6/$%

USG Shaftwall/Area Separation Walls · Aluminum Break Away Clips for H-Stud Systems · Deep Leg J-Track · J-Runner 34 mil · JL Corner · Jamb Strut · H-Stud 34 mil · H- 

USG Fire Resistant Assemblies Wall Penetration Details (English) - J2133 SECTION PLAN USG SHEETROCK ©BRAND FIRECODE CORE GYPSUM PANELS USG SHEETROCK FIRECODE ® COMPOUND PIPE COVERING AND THROUGH PENETRATION WALL ASSEMBLY Scale: 3" = 1' - 0" SYSTEM NO. W-L-5044 9

Shaftwall System consists of 1" shaftliner panels supported by 2-1/2", 4" or 6" C-T Studs and faced on one side with two layers of 1/2" fire code board.

Gyprock Shaft Systems are not suitable for certain walls of Class 9B buildings which require 1.0kPa loading. Resistance to Impact A series of impacts from a 27.2kg sandbag are imposed on a typical wall section and must not cause permanent damage.

Shaft Wall-AER-09038 SCALE: DATE: UNITED STATES GYPSUM COMPANY This Shaft Wall Detail must not be used without a complete evaluation by the owner's design professional--to

This SHAFT WALL SYSTEM DETAIL must not be used without a complete evaluation by the owner's design professional to verify the suitability of the design for a given structure. 1" SHEETROCK BRAND LINER PANELS USG STEEL 2" H STUD 3 4" AIR SPACE (MIN.) 1" SHEETROCK BRAND LINER PANELS 3 1/2" LINE OF ADJACENT FRAMING MIN. STEEL 6" C-RUNNER 20 GA.

USG Shaft Wall Systems are non-load-bearing gypsum wall partition asse mblies constructed from outside the shaft at each loor. Shafts are enclosed early in construct ion, and the walls are inished later, along with interior partitions. Installation is quick and ea sy, using components and application procedures familiar to drywall contractors.

USG SHEETROCK ©BRAND SHAFT LINER GYPSUM PANELS, CUT TOP OF PANEL 1" LESS THAN FLOOR TO CEILING HEIGHT, TYPICAL Scale: 3" = 1' - 0" HEAD OF WALL UL HW-D-0611 (1 AND 2 HOUR) 7 USG SHEETROCK © BRAND FIRECODE CORE GYPSUM PANELS, CUT

1" (25.4 mm) DensGlass Shaftliner panels may be abutted, spliced or stacked within the cavity. The shorter panel should be a minimum 2' (610 mm) tall to engage two stud tabs on each panel edge. Joints of adjacent panels should be alternately stacked or staggered to prevent a continuous horizontal joint.

USG Shaft Walls provide up to 4-hour fire resistance and sound ratings to 51 STC. They resist intermittent lateral loads up to 15 psf; also resist fatigue 

Horizontal Shaftwall Designed for ceiling or duct shaft and composed of 1" (25.4 mm) ToughRock® Shaftliner or DensGlass® Shaftliner panel supported by 2-1/2" (64 mm), 4" (102 mm) or 6" (152 mm) C-T studs and three layers of 1/2" (12.7 mm) ToughRock® Fireguard C® or 1/2" (12.7 mm) DensArmor Plus® Fireguard C® gypsum board. Hourly Rating: 2-hour

The Cavity Shaft Wall System includes components that provide the strength to withstand lateral loads and fire protection necessary for walls that enclose elevator shafts, stairwells and other

Shaft wall limiting heights spans shaft wall limiting heights spans shaft wall limiting heights spans shaft wall ch stud

Shaftliner™ panels are specially manufactured plasterboard developed for use in USG Boral systems such as Partiwall®, IntRwall™ and Shaftwall™ systems. As you 

Our Shaftwall Metal Framing can be installed for vertical and horizontal encasement applications. With the help of a variety of mold, moisture, and fire-resistant gypsum and cement boards that

Technical Support 1-800-USG-4YOU Product Safety Hotline 1-800-507-8899 Product Categories

OVERVIEW CGC Shaft Wall Systems are non-load-bearing gypsum wall partition assemblies constructed from outside the shaft at each floor. Shafts are enclosed early in construction, and

Assemblies Directory & Design Details USG offers professionals a complete set of architectural drawings for planning and estimation. Whether you need exterior design detail drawings or interior design detail drawings, make the most informed decisions with our comprehensive UL assemblies directory and UL assembly details.

USG Middle East’s ever-growing portfolio of groundbreaking ceilings systems, drywall assemblies, and end-to-end solutions is backed by unparalleled quality service. With an extensive distribution and sales network operating for more than 25 years across the MENA Region, our dedicated teams provide local expertise and high levels of support in finding the right solutions for your

For details of steel framed Partiwall system refer to USG Boral The clear distance between the SHAFTLINER fire barrier and wall framing on both sides 

Use CGC Shaft Wall Systems to construct elevator shafts, mechanical shafts, stairwells, air return shafts and horizontal membranes. These shafts are vital for vertical communication, power, water, fresh air, exhaust and a means of egress. Solid Shafts Horizontal Stud Shafts

USG Shaft & Stair Walls Systems meet the requirements of 1-hour, 2-hour, and 3-hour fire resistive rated assemblies when tested in accordance with ASTM E119 and 

USG Shaft Wall Systems are non-load bearing gypsum wall partition assemblies constructed from outside the shaft at each floor.

5. For more details and construction methods, refer to UL Design #U415 System A and the USGinstallation instructions. Two-Hour Cavity Shaft Wall (Non-Load Bearing), See Figure 2 1. A minimum 2-1/2-in deep 24 gauge floor and ceiling J-runners, attached to

USG Fire-Resistant Assemblies Catalog - SA100 Fire-Stop Systems Brochure - SA727 USG Cavity Shaft Wall Systems Catalog - SA926 USG Acoustical Assemblies Brochure (English) -

A 2-hour fire-resistive, non-load bearing non-combustible partition designed to enclose shaftwalls, containing elevators, ducts, piping, air shafts and similar construction applications. System consists of 1" shaftliner panels supported by 2-1/2", 4" or 6" C-T studs and faced on one side with two layers of 1/2" Type C or 5/8" Type X gypsum board.